dr.ir. T.C. Bor (Ton)

Engineering & Materials Science

# Friction Stir Welding
# Lasers
# Polymers
# Powders
# Pressure Vessels
# Tapes

Chemistry

# Mandrel
# Pressure Vessel

Faculty of Engineering Technology (ET), Production Technology (PT)

Zaami, A. , Baran, I. , Bor, T. C. , & Akkerman, R. (2021). Optical characterization of fiber-reinforced thermoplastic tapes for laser-based composite manufacturing. Composites Part A: Applied Science and Manufacturing, 146, [106402]. https://doi.org/10.1016/j.compositesa.2021.106402

Zaami, A. (2021). Development of a fast local analysis tool for optimized laser assisted tape winding. University of Twente. https://doi.org/10.3990/1.9789036551205

Zaami, A., Schäkel, M. , Baran, I. , Bor, T. C., Janssen, H. , & Akkerman, R. (2021). A fully coupled local and global optical-thermal model for continuous adjacent laser-assisted tape winding process of type-IV pressure vessels. Journal of composite materials, 55(8), 1073-1090. https://doi.org/10.1177/0021998320944598

Zaami, A. , Baran, I. , Bor, T. C. , & Akkerman, R. (2020). New process optimization framework for laser assisted tape winding of composite pressure vessels: Controlling the unsteady bonding temperature. Materials & Design, 196, [109130]. https://doi.org/10.1016/j.matdes.2020.109130

Cordova, L. , Bor, T., de Smit, M., Carmignato, S., Campos, M. , & Tinga, T. (2020). Effects of powder reuse on the microstructure and mechanical behaviour of Al-Mg-Sc-Zr alloy processed by laser powder bed fusion (LPBF). Additive manufacturing, 36, [101625]. https://doi.org/10.1016/j.addma.2020.101625

Zaami, A. , Baran, I. , Bor, T. C. , & Akkerman, R. (2020). 3D Numerical modeling of laser assisted tape winding process of composite pressure vessels and pipes-effect of winding angle, mandrel curvature and tape width. Materials, 13(11), [2449]. https://doi.org/10.3390/MA13112449

Cordova, L. , Bor, T., de Smit, M., Campos, M. , & Tinga, T. (2020). Measuring the spreadability of pre-treated and moisturized powders for laser powder bed fusion. Additive manufacturing, 32, [101082]. https://doi.org/10.1016/j.addma.2020.101082

Cordova Gonzalez, L. (2020). Exploring the influence of powder properties and handling on the selective laser melting process. University of Twente. https://doi.org/10.3990/1.9789036549455

Zaami, A., Schäkel, M. , Baran, I. , Bor, T. C., Janssen, H. , & Akkerman, R. (2020). Temperature variation during continuous laser-assisted adjacent hoop winding of type-IV pressure vessels: An experimental analysis. Journal of composite materials, 54(13), 1717-1739. https://doi.org/10.1177/0021998319884101

Cordova, L. , Bor, T., Campos, M. , & Tinga, T. (2019). Drying strategies to reduce the formation of hydrogen porosity in Al alloys produced by Additive Manufacturing. Paper presented at VII Congreso Español de Pulvimetalurgia y II Congreso Iberoamericano de Pulvimetalurgia, CEIPM 2019, Madrid, Spain. https://easychair.org/publications/preprint/V1ld

Bekijk alle publicaties van deze medewerker

Vakken in het huidig collegejaar worden toegevoegd op het moment dat zij definitief zijn in het Osiris systeem. Daarom kan het zijn dat de lijst nog niet compleet is voor het gehele collegejaar.

+31534892453

+31534892502 (bij geen gehoor)

t.c.bor@utwente.nl

Bezoekadres

Universiteit Twente
Faculty of Engineering Technology
Horst Complex (gebouwnr. 20), kamer N203
De Horst 2
7522LW Enschede

Navigeer naar locatie

Postadres

Universiteit Twente
Faculty of Engineering Technology
Horst Complex N203
Postbus 217
7500 AE Enschede

Faculty of Engineering Technology (ET), Production Technology (PT)

Universiteit Twente Drienerlolaan 5
7522 NB Enschede

+31 (0)53 489 9111
info@utwente.nl
Route

Welkom...

Universitair hoofddocent

Expertises

Verbonden aan

Publicaties

Pure Link

Vakken Collegejaar 2022/2023

Vakken Collegejaar 2021/2022

Contactgegevens

Bezoekadres

Postadres

Verbonden aan